date of publication：2019-8-29 22:58:33 publisher：anshan libang compressor co., ltd.
adsorption dryer achieves drying effect through "pressure change" (principle of pressure swing adsorption). because the capacity of air to hold water vapor is inversely proportional to the pressure, a part of the air after drying (called regenerated gas) is decompressed and expanded to the atmospheric pressure. this pressure change makes the expanded air drier, and then it flows through the regenerated drying agent layer (i.e. the drying tower that has absorbed enough water vapor) without connecting the air flow. the regeneration gas absorbs the water in the desiccant and takes it out of the desiccant to achieve the purpose of dehumidification. the two towers work in a cycle without heat source and continuously supply dry compressed air to the user's gas system.
the sorbent dryer is classified by sorbent regeneration method, which can be divided into two types: non-thermal regeneration micro-thermal regeneration dryer and thermal regeneration micro-thermal regeneration dryer. because the non-thermal micro-heat regeneration dryer works according to isothermal adsorption, also known as "pressure swing adsorption" and "temperature swing adsorption" with thermal micro-heat regeneration dryer works according to isobaric adsorption, also known as "temperature swing adsorption". in practical use, there is also a kind of micro-thermal dryer. in form, the micro-thermal regenerative dryer also warms up the regenerative gas. but because the regenerative gas it uses comes from the dry air with very low water content, it is also a "pressure swing adsorption" dryer.
anshan libang compressor co., ltd.-乐鱼官网入口网页版
|
parameter \ model
|
lbx—1.0
|
lbx—2.0
|
lbx—3.0
|
lbx—6.0
|
lbx—10
|
lbx—15
|
|
rated air handling capacity nm3/min
|
1
|
2.4
|
3.8
|
6.5
|
13.5
|
18
|
|
working pressure pma
|
0.4—1.0
|
0.4—1.0
|
0.4—1.0
|
0.4—1.0
|
0.4—1.0
|
0.4—1.0
|
|
intake temperature ℃
|
≤45
|
≤45
|
≤45
|
≤45
|
≤45
|
≤45
|
|
inlet oil content ppm
|
≤0.01
|
≤0.01
|
≤0.01
|
≤0.01
|
≤0.01
|
≤0.01
|
|
adsorbent
|
aluminum glue or molecular sieve
|
aluminum glue or molecular sieve
|
aluminum glue or molecular sieve
|
aluminum glue or molecular sieve
|
aluminum glue or molecular sieve
|
aluminum glue or molecular sieve
|
|
regeneration mode
|
non-thermal regeneration (micro-thermal regeneration)
|
|
operation mode
|
alternating continuous operation of two towers
|
|
regeneration gas consumption
|
12﹪-15﹪（6﹪）
|
12﹪-15﹪（6﹪）
|
12﹪-15﹪（6﹪）
|
12﹪-15﹪（6﹪）
|
12﹪-15﹪（6﹪）
|
12﹪-15﹪（6﹪）
|
|
control mode
|
conventional intensive electricity or single chip microcomputer control
|
|
(micro-heating) heater power
|
1
|
1.5
|
2
|
2.5
|
3
|
5
|
|
dryness of finished gas
|
pressure dew point：—20℃~—40℃（—40℃~—70℃）
|
|
particle size of dusty product gas
|
≤0.01µm
|
≤0.01µm
|
≤0.01µm
|
≤0.01µm
|
≤0.01µm
|
≤0.01µm
|
|
length * width * height
|
980×420×1200
|
1080×420×1550
|
1080×420×1550
|
1200×700×2050
|
1600×720×2420
|
1600×72×2420
|
|
inlet and outlet caliber
|
zg1″external teeth
|
dn25fl
|
dn25fl
|
dn40fl
|
dn50fl
|
dn80fl
|
|
installation mode
|
installation of upright flat ground foot
|
|
weight kg
|
180（190）
|
300（305）
|
350（390）
|
510（550）
|
780（910）
|
900（1060）
|